HANDGUN

Ruger NICKEL 90231 Magazine for Mark 3 4 IV Standard Frame Pistols

WILL NOT FIT 22/45Factory Ruger 90231 10 round magazine is what Ruger shipped with new Mark 3 and ships with Mark 4 pistols.This magazine will also work in Mark 2 and Mark 1 pistols.For older Mark 1 (right hand follower button) you will need to swap...

Ruger NICKEL 90599 Magazine for Mark IV 4 22/45

WILL NOT FIT STANDARD FRAMES ONLY FITS 22/45 FRAMES.ALL Ruger LITE are 22/45 from the factory.Factory Ruger 90599 10 round magazine is what Ruger ships with new Mark 4 - 22/45 pistols.This magazine will also work in Mark 2 - 22/45 and Mark 3 - 22/45...

Ruger NEW Take Off Mark IV 4 22/45 Grip Frame Lower Removable Plastic Grip Panels (also fits and Volquartsen Mamba)

New Take OffRuger Mark IV 22/45 frame *POST RECALL* 500 seriesRuger DOES NOT sell these to anyone they only come from parting out pistols.You can attach ANY Ruger Mark IV upper to this and Aftermarket Mark IV Uppers CLICK HERE TO SEE SOMENO TRANSFER...

Factory Ruger Mark Series Pistol Rebound Spring Mark 1, 2, 3, 4 IV & All 22/45 *A6

Factory Ruger Rebound Spring (firing pin spring) fits ALL Mark Series Pistols ever made.(**The very first 1949 - 1952 production years could differ, best to observe closely on these**)Have seen these mangled before but I think the firing pin was...

Volquartsen SureFeed Magazine Follower Spring for Ruger Mark III and IV 5 PACK VC4FS-5

The SureFeed Magazine Follower Spring for the Ruger MKIII and MK IV is 25% stronger than the factory spring. The increased spring rate improves feeding in all Ruger MKIII and MK IV magazines. The SureFeed Magazine Follower Spring will eliminate feeding...

Volquartsen VS3 Recoil Rod Spring and Assembly Kit for Ruger Mark 1, 2, 3, 4 and ALL 22/45 and LITE VC3RS

Recoil spring assembly is designed for a variety of pistols: Volquartsen: Scorpion, Mamba, Habu, Ruger: MKI, MKII, MKIII, MKIV and ALL Ruger 22/45And ALL TacSol Pac-LiteThis innovative design makes it quick and easy to match your spring weight to your...

Factory Ruger Mark IV 4 Bolt Stop Spring *C11

Factory Ruger Mark IV Bolt Stop SpringONLY for Mark IV PistolsThese seem to get lost quite a bit so we will be keeping them in stock now.If you bolt stop is not working properly this may fix it.Part #4 in Mark IV Standard manual, #5 in Mark IV 22/45...

Factory Ruger Rebound Spring Support for Mark 1 2 3 4 IV & All 22/45 Pistols *A5

Factory Ruger Rebound Spring Support (firing pin spring support) fits ALL Mark Series Pistols ever made**.(**The very first 1949 - 1952 production years could differ, best to observe closely on these**)This holds the rebound spring (firing pin spring)...

Ruger Blued Scope Base Filler HEX Allen Screws for Mark 1 2 3 4 IV & All 22/45 with Factory Drilled Holes *D12

Ruger Blued Scope Base Filler Allen Screws for Mark Series Pistols with Factory Drilled Holes6-48 NF

Ruger Mark IV 4 NEW Take Off Upper 5.5" Bull Barrel with Sights 40107

FFL REQUIREDNew Take OffRuger 5.5" Bull Steel UpperFits ALL Mark IV FramesBoth Standard and 22/45Comes with Sights and nothing else.5.5" barrel19.3 oz.This is an FFL item***We DO NOT Hunt down FFL's without charging for it***Your Dealer MUST get a copy...

Ruger 9 round 90062 Magazine with SILVER Base for Mark 1

WILL NOT FIT 22/45Factory Ruger 90062 9 round magazine with SILVER BASEFor Mark 1 pistolsFor older Mark 1 (right hand follower button) you will need to swap the button to the right side. The follower can be swapped out to make it 10 round.The button...

Factory Ruger 22/45 Mark 3 and 4 IV and LITE Grip Screw *F12

MARK 3 --- ONLY FITS 22/45 and LITE with removable panelsMARK 4 (IV)--- Fits all 22/45 and LITE pistols (except LITE with STANDARD FRAME) These use 3/32" Allen Driver.SINGLE SCREW NOT A SETNOT FOR ANY STEEL OR ALUMINUM FRAME RUGER MARK PISTOL

Factory Ruger Safety Detent Plunger for Mark 1 2 3 & 22/45 Mark 2 3 & Mark 3 LITE Pistols *B13

Factory Ruger Safety Detent Plunger Fits ALL Mark Series PRIOR Mark IV.(The very first 1949 - 1952 production years could differ, best to observe closely on these)These are THE most commonly lost part when taking the pistol apart. If your safety is not...

Factory Ruger Extractor Spring Mark 1, 2, 3, 4 IV & All 22/45 and 10/22 Rifle *A1B*

Factory Ruger Extractor Spring fits ALL Mark Series Pistols ever made.(**The very first 1949 - 1952 production years could differ, best to observe closely on these**)ALSO fits ALL 10/22 Rifles and ChargersIf you're having extraction issues, it's a good...

Mark IV 4 LITE NEW Take Off Upper Threaded 1/2"x28 Diamond Gray Anodized with Rail and Sights 43918

Ruger LITE in Diamond Gray AnodizedFits ALL Mark IV FramesBoth Standard and 22/45Stainless Steel Breech FaceTHREADED  1/2"x28Comes with Rail, Sights, Thread Protector, Wave Washer and nothing else.4.4" barrel9.9 oz.This is an FFL item***We DO NOT...

Volquartsen Loaded Chamber Indicator Filler (LCI) for Ruger Mark 3 Stainless- VC3LCI-S

Comes with anchor screw and Allen wrenchLoaded Chamber Indicator Filler (LCI) for the Ruger MK3 is wire EDM cut from stainless steel.

Factory Ruger Magazine (90599) Base Block 22/45 Mark IV 4

Factory Ruger magazine base to convert your older 22/45 or standard frame magazines to fit MK IV 22/45Will convert the following magazines; 90045 (MK2 22/45), 90231 (MK3, MK4 Standard Frame), 90229 (MK3 22/45) Click Here for our page on how to properly...

Factory Ruger Extractor Plunger Mark 1 2 3 4 IV & All 22/45 *A1

Factory Ruger Extractor Plunger fits MOST Mark Series Pistols ever made.(The early Mark 1 Bolts used a shorter plunger and this won't work in them)Part Number: A02501

Volquartsen SureFeed Magazine Follower Spring for Ruger Mark III and IV 2 PACK

The SureFeed Magazine Follower Spring for the Ruger MKIII and MK IV is 25% stronger than the factory spring. The increased spring rate improves feeding in all Ruger MKIII and MK IV magazines. The SureFeed Magazine Follower Spring will eliminate feeding...

Factory Ruger Mark IV 4 Magazine Ejector Assist Spring *STANDARD FRAMES ONLY* *C21*

Factory Ruger Mark IV 4 Magazine Ejector Assist SpringWill NOT fit anything but MARK IVSTANDARD frame ONLYPart #48 in Ruger ManualPart Number: VN04100The Ejector Assist is HEREThe Magazine Ejector PLUNGER is HERE

Ruger NEW Take Off Mark IV 4 Standard Black Aluminum Grip Frame Lower

New Take OffRuger Mark IV Standard Aluminum frame *POST RECALL* 500 seriesRuger DOES NOT sell these to anyone they only come from parting out pistols.You can attach ANY Ruger Mark IV upper to this and Aftermarket Mark IV Uppers CLICK HERE TO SEE SOMENO...

Ruger Compensator Wave (crush, lock, spring) Washer Same one that comes on Ruger LITE *B19*

BRAND NEW Ruger Wave washer for Compensators or any muzzle device that uses this type washer for 1/2"-28 threads. ONLY .017" THICK (when flat) .53 ID x .77 OD.

Ruger Magazine 90231, 90046, 90062 BASE BLOCK for Ruger Mark 2 3 4 IV Standard Frame Pistols (NOT 22/45)

WILL NOT FIT 22/45Factory Ruger 90231 Base BlockThis is the base that is used on 90231 and 90046 magazinesIt is also the same as what is used on 90062 only in BlackYou can use this to change your 90229 and 90599 magazines to fit Standard frames vs...

Factory Ruger Grip Screws for Mark 1 2 3 4 IV (NOT 22/45) Pistols Standard Frame

WILL NOT FIT ANY 22/45 Factory Ruger Grip Screws fit Standard Frames Mark 1, 2, 3, 4These are 3/16" shank. These use 3/32" Allen Driver.

Bolt Stop Pin and V-Lock Retainer Spring for MK IV

Mark IV Bolt Stop Pin and V-Lock Retainer SpringModel: VF4BPUPC: 810162019976See our other Volquartsen Mark IV parts HERE!

Volquartsen Black Extended Bolt Release for Ruger Mark 4 IV for 22/45 (Mamba) VC4SR-45-B

ONLY for 22/45Finding it too hard release the bolt on the MK IV 22/45? This extended bolt release gives you more surface area and deep serrations for easy thumb engagement. The bolt release pad is CNC mac hined from 416 stainless and extends ...

Volquartsen Black Extended Magazine Release For Ruger Mark IV 22/45 VC4MR

Fits Ruger Mark 4 22/45 frames The MKIV Extended Magazine Release allows the magazine to sit higher in the frame. This improves feeding by preventing the bolt from sliding over the round in the magazine. UPC: 810162018078Model: VC4MR

Volquartsen Accurizing Kit, Mark 4 IV, Black Trigger VC4AK

The complete drop-in kit comes complete with: -CNC Machined Disconnector -Target Hammer, Hammer Bushing-Target Sear, Sear Spring-Target Trigger with plunger and spring *also comes with pretravel and overtravel adjustments. The Accurizing Kit for...

Volquartsen 22/45 Mainspring for Ruger Mark 2, 3 Pistols Black- VC3MSR-45-B

WILL NOT FIT ANY STANDARD FRAME(click here Mark 1, 2, 3 standard frame Volquartsen mainspring)Complete mainspring assembly designed for the Ruger MKII or MKIII. Mainspring components are wire EDM-cut and CNC-machined.Mainspring does not feature the lock...

Volquartsen Bolt Tune-up Kit for Ruger Mark 1, 2, 3, 4 and ALL 22/45 and LITE

Ruger Mark IV 4 STANDARD NEW Take Off Upper 6" Standard Taper Barrel with Sights 40105

New Take OffRuger 6" Standard Taper Steel UpperGreat start for a Custom Barrel Project or internally suppressed project.From a technical stand, it is longer and lighter than the 5.5 Bull and offers great balanceDrilled and tapped for a Rail MountFits ALL...

Ruger Mark IV Washer to remove Right Hand Safety *C2

Ruger Mark IV washer to replace RIGHT hand safety lever when you want it removed.

Factory Ruger Mark IV 4 Magazine Ejector Assist Plunger *STANDARD FRAMES ONLY* *C20*

Factory Ruger Mark IV 4 Magazine Ejector Assist PlungerWill NOT fit anything but MARK IVSTANDARD frame ONLYPart #49 in Ruger ManualPart Number: VN04600The Ejector Assist is HEREThe Magazine Ejector SPRING is HERE

Ruger NEW Take Off Mark IV 4 22/45 Grip Frame Lower *GOLD Trigger - Ruger Logo Rubber Grips made by Hogue (also fits and Volquartsen Mamba)

New Take OffRuger Mark IV 22/45 frame *POST RECALL* 500 seriesRuger DOES NOT sell these to anyone they only come from parting out pistols.You can attach ANY Ruger Mark IV upper to this and Aftermarket Mark IV Uppers CLICK HERE TO SEE SOMENO TRANSFER...

Ruger Magazine Block Retaining Plunger for ALL Modern Ruger "Mark" Pistol Magazines 1 2 3 4 IV & all 22/45

This Plunger fits in ALL Mark series magazines with the plastic base pads (from factory)Will NOT fit old chrome base Mark 1 magazines.These can get shot into another dimension when disassembling a magazine. Click Here for our page on how to properly...

Ruger NICKEL 90229 Magazine for Mark 3 22/45

WILL NOT FIT MK-IV 22/45Factory Ruger 90229 10 round magazine is what Ruger shipped with new Mark 3 - 22/45 pistols.This magazine will also work in Mark 2 - 22/45 pistol. Click Here for our page on how to properly adjust your magazines to feed properly...

Factory Ruger Take Off Mark IV 4 Bolt *Stripped*

Factory Ruger Mark 4 Bolt removed from NEW unfired PistolsALL INTERNAL PARTS REMOVEDThese will work in Mark 2 pistols and in Mark 3 IF the LCI is removed

Volquartsen Mark IV Bedding Gel

Volquartsen Mark IV Bedding GelIncrease your Mark IV's accuracy and reliability with Volquartsen's custom-designed new Mark 4 Bedding Gels. It has an adhesive backing for easy installation and works to eliminate any play between the frame and upper. ...

Volquartsen Loaded Chamber Indicator Filler (LCI) for Ruger Mark 3 Black- VC3LCI-B

Comes with anchor screw and Allen wrenchLoaded Chamber Indicator Filler (LCI) for the Ruger MK3 is wire EDM cut from stainless steel.

Volquartsen Magazine Follower Button for Ruger Mark 1, 2, 3, 4 Pistols - 10 Pack NEW style

Have a sluggish MKII, MKIII, MK IV, or 22/45 Ruger magazine? Chances are the spring is fine but the actual culprit is the metal on metal contact of the magazine button. Not only does this make magazines hard to load but it can also cause feeding...

TacSol Tactical Solutions Heavy Duty Ejector for Ruger Mark series pistols and Pac-Lite

Tactical Solutions HEAVY DUTY Ejector for Tac-Sol Pac-Lite AND ALL Mark Series Pistols (1, 2, 3, 4, 22/45, LITE) from 1949 till present. Replacement for factory ejector is precision machined from hardened 416 stainless steel billet for extra strength and...

Ruger Mark IV 4 NEW Take Off Upper 5.5" Bull Barrel with Rail Only 40107

FFL REQUIREDNew Take OffRuger 5.5" Bull Steel UpperFits ALL Mark IV FramesBoth Standard and 22/45Comes with Rail and nothing else.5.5" barrel19.3 oz.This is an FFL item***We DO NOT Hunt down FFL's without charging for it***Your Dealer MUST get a copy of...

Factory Ruger Mark IV 4 Magazine Ejector Assist *STANDARD FRAMES ONLY* *C19*

Factory Ruger Mark IV Magazine Ejector AssistWill ONLY fit MARK IV STANDARD Frames (Metal) Part #47 in Ruger ManualPart Number: A402565The Ejector Assist Plunger is HEREThe Ejector Assist Spring is HERE

Factory Ruger Mark IV 4 Latch Spring Set *A9* x2

WILL NOT FIT ANYTHING BUT MARK IVFITS ALL Mark IV Frames Latch Spring SetFor the push button takedown latch.Factory Ruger partPart Number: KA04600

Ruger NEW Take Off Mark IV 4 Standard Stainless Steel Grip Frame Lower

New Take Off Frame from brand new Mark IV PistolsRuger Mark IV Standard Stainless Steel frame *POST RECALL* 500 seriesRuger DOES NOT sell these to anyone they only come from parting out pistols.You can attach ANY Ruger Mark IV upper to this and...

Factory Ruger Reversible Picatinny Rail for ALL Factory Drilled/Tapped Mark 1 2 3 4 IV Pistols, 22/45 and Tac-Sol Pac-Lite (Pac-Lite needs different screws) 90623

Ruger Reversible Picatinny Rail for ALL Mark Series PistolsWorks on FACTORY-DRILLED Mark Series Pistols.Same rail that ships with Ruger Mark IV LITE and Tactical Series Pistols-reversible-4-3/8" long-black aluminum-3 screws included (6-48 threads)3...

Factory Ruger Bolt Stop Pivot Pin Stainless for Mark 1, 2, 3 Pistols also 22/45 MK 2 3 *B11

Bolt Stop Pivot Pin Fits Ruger Mark Series 1, 2 or 3 and 22/45 and MK3 LITE Pistols. NOT FOR MARK 4These pop out sometimes and get lost.Part Number: KA02602

Factory Ruger Bolt Stop Pin Blued for Mark 1, 2, 3 Pistols also MK 2 3 22/45 *B12

Factory Ruger Bolt Stop Pin in BluedFits Mark 1, 2 or 3 and 22/45 Mark 2, 3 and Mark 3 LITE Pistols. Not something commonly needed but can provide contrast when mixing stainless and blued (stainless version found HERE)NOT FOR MARK 4Part Number: A00100

Volquartsen Competition Kit, Mark 4 IV, Black Trigger (Mamba)

The Competition Kit is the "Accurizing Kit" WITH a SureStrike Firing Pin and Exact Edge ExtractorFits **ALL** Ruger Mark IV pistols,, yes ALL of them.If your pistol says "Ruger Mark IV" anyplace this kit fits it. The complete drop-in kit comes...

Volquartsen Accurizing Kit, Mark 4 IV, NO Trigger VC4AK-NT

Want to use your own or a different trigger?Just buy the lock work with this kit!The complete drop-in kit comes complete with: -CNC Machined Disconnector -Target Hammer, Hammer Bushing-Target Sear, Sear Spring-Target Trigger with plunger and...

Volquartsen Standard Mainspring for Ruger Mark 1, 2, 3 Pistols Black- VC3MSR-3-B

WILL NOT FIT ANY 22/45 FRAME(click here Mark II, III 22/45 frame Volquartsen mainspring)Complete mainspring assembly designed for the Ruger MKII or MKIII. Mainspring components are wire EDM-cut and CNC-machined.Mainspring does not feature the lock...

Volquartsen Hammer and Bushing for Ruger Mark 1, 2, 3 and ALL 22/45 and LITE **READ DESCRIPTION**

This is the same Hammer and Bushing that comes in ALL MK2 and MK4 Volquartsen Accurizing KitsThis kit will work in ALL MK1, MK2, MK3 and MK4 (see notes below) Ruger Pistols (Very early MK1 may vary)You MUST have the COMPLETE "Accurizing" or...