Ruger 22/45 Mark 2, 3 Parts including MK3 LITE

Volquartsen VS3 Recoil Rod Spring and Assembly Kit for Ruger Mark 1, 2, 3, 4 and ALL 22/45 and LITE VC3RS

Recoil spring assembly is designed for a variety of pistols: Volquartsen: Scorpion, Mamba, Habu, Ruger: MKI, MKII, MKIII, MKIV and ALL Ruger 22/45And ALL TacSol Pac-Lite Part # VC3RSUPC # 810162014377This innovative design makes it quick and easy to...

Volquartsen Loaded Chamber Indicator Filler (LCI) for Ruger Mark 3 Black- VC3LCI-B

Comes with anchor screw and Allen wrenchLoaded Chamber Indicator Filler (LCI) for the Ruger MK3 is wire EDM cut from stainless steel.

Volquartsen SureFeed Magazine Follower Spring for Ruger Mark III and IV 5 PACK VC4FS-5

The SureFeed Magazine Follower Spring for the Ruger MKIII and MK IV is 25% stronger than the factory spring. The increased spring rate improves feeding in all Ruger MKIII and MK IV magazines. The SureFeed Magazine Follower Spring will eliminate feeding...

Volquartsen Loaded Chamber Indicator Filler (LCI) for Ruger Mark 3 Stainless- VC3LCI-S

Comes with anchor screw and Allen wrenchLoaded Chamber Indicator Filler (LCI) for the Ruger MK3 is wire EDM cut from stainless steel.

Volquartsen Mark 4 IV and Mark 2 DLC Black Competition Bolt (Mamba, Scorpion)- VC4BT-B

Fits ALL Mark 2 and ALL Mark 4 ALL Standard and 22/45 and LITE Will fit ALL Mark 3 if LCI is removed from receiver or replaced by a filler.Are you a competitive shooter looking to eliminate stovepipes, failures to fire and improve the overall performance...

Volquartsen Magazine Follower Button for Ruger Mark 1, 2, 3, 4 Pistols - 2 Pack NEW style

Have a sluggish MKII, MKIII, MK IV, or 22/45 Ruger magazine? Chances are the spring is fine but the actual culprit is the metal on metal contact of the magazine button. Not only does this make magazines hard to load but it can also cause feeding...

Factory Ruger Recoil Rod Spring Assembly for ALL Ruger Mark IV 4

Factory Ruger Recoil Spring Assembly for Mark IV.We have been running these in older MK1, MK2, MK3 pistols with no problems. They no longer sell the KA-57 assemblySeen these bent, worn out and lost.

Gunsmither Pistol Pal Tool for Ruger Mark 1 2 3 both Standard and 22/45 Pistols

If you have a Ruger Mark 1, 2 or 3 you NEED this tool! (SEE PICS)For Mark 4 this tool is only useful for removing Extractor from BoltI have one in my range bag and in my tool box.Use it to hook the Mainspring Latch Lever so you can unlock itUse it to...

Volquartsen Bolt Tune-up Kit for Ruger Mark 1, 2, 3, 4 and ALL 22/45 and LITE VC3FE

The Volquartsen Bolt Tune-Up Kit for the Ruger MKI, MKII, MKIII, and MK IV target pistols contains the Exact Edge Extractor for MKII, MKIII, MK IV, and 10/22 and the SureStrike Firing Pin for MKI, MKII, MKIII, and MK IV. This kit will eliminate light...

Volquartsen 22/45 Auto Bolt Release for Ruger Mark 3 ONLY Pistols Black VC3SPL-B

WILL NOT FIT ANY STANDARD FRAMEWas told by customer will NOT fit 22/45 Mark 2 eitherThey have made releasing the bolt on the Ruger 22/45 easier. No more having to manually operate the bolt hold open lever to release the bolt. Simply pull back on the bolt...

Volquartsen Magazine Follower Button for Ruger Mark 1, 2, 3, 4 Pistols - 10 Pack NEW style

Have a sluggish MKII, MKIII, MK IV, or 22/45 Ruger magazine? Chances are the spring is fine but the actual culprit is the metal on metal contact of the magazine button. Not only does this make magazines hard to load but it can also cause feeding...

Volquartsen VS3 Recoil Rod Replacement Spring HEAVY for Ruger Mark 1, 2, 3, 4 and ALL 22/45 and LITE VC3RS GOLD

Replacement Spring for the VC3RS Kit ORIif you know what you are doing you can replace your spring on your factory Ruger KA-57 AssemblyGold, heavy weight spring, for high velocity ammo.10% stronger than Standard spring

Volquartsen VS3 Recoil Rod Replacement Spring LIGHT for Ruger Mark 1, 2, 3, 4 and ALL 22/45 and LITE VC3RS BLACK

Replacement Spring for the VC3RS Kit ORIf you know what you are doing you can replace your spring on your factory Ruger KA-57 AssemblyLIGHT (Black) 10% Reduction vs. Standard springThis spring can be used for a softer recoil with standard velocity ammo...

Volquartsen Hammer Bushing for Ruger Mark 1, 2, 3 and ALL 22/45 and LITE

This is the same bushing that comes in ALL Volquartsen Accurizing KitsAlthough it can be used with a Factory Ruger MK3 hammer it is NOT advised by Volquartsen (but we have done it ;)I do not know how it would work with a Factory Ruger MK4 hammer so,...

Volquartsen Target Sear for Ruger Mark 1, 2, 3 VC2TS

Fits Ruger Mark 1, 2, 3 and 22/45 Mark 2, 3 and Mark 3 LITEThis specially designed sear provides the shooter with a shorter, faster, cleaner breaking trigger pull. The sear is wire EDM-cut from hardened A2 tool steel.   Part # VC2TS UPC 810162011680

Volquartsen SureFeed Magazine Follower Spring for Ruger Mark III and IV 2 PACK

The SureFeed Magazine Follower Spring for the Ruger MKIII and MK IV is 25% stronger than the factory spring. The increased spring rate improves feeding in all Ruger MKIII and MK IV magazines. The SureFeed Magazine Follower Spring will eliminate feeding...

Volquartsen Mark 2, 3, & 22/45 Extended Safety Stainless

Fits ALL Ruger Mark 2 and Mark 3 Pistols with STANDARD FRAMESFits 22/45 Mark 3 frames, DOES NOT FIT 22/45 MARK 2 FRAMESThe Extended Safety provides the shooter improved access to the safety on the Ruger MK2, MK3 and MK3 22/45 pistol. The ...

Volquartsen Accurizing Kit Fits Mark 1 2 3 Black Trigger (Scorpion)

THIS is the kit you want for your Mark 3 to remove Magazine safety. Complete drop-in kit comes complete with:-Target Hammer-Target Sear-Target Trigger (available in a variety of colors)-Extended Bolt Release-Trigger Return Spring with...

Volquartsen 22/45 Mainspring for Ruger Mark 2, 3 Pistols Black- VC3MSR-45-B

WILL NOT FIT ANY STANDARD FRAME(Click Here for Mark 1, 2, 3 STANDARD frame Volquartsen mainspring)Complete mainspring assembly designed for the Ruger MKII or MKIII. Mainspring components are wire EDM-cut and CNC-machined.   Mainspring does not...

Volquartsen Hammer and Bushing for Ruger Mark 1, 2, 3 and ALL 22/45 and LITE **READ DESCRIPTION**

This is the same Hammer and Bushing that comes in ALL MK2 and MK4 Volquartsen Accurizing KitsThis kit will work in ALL MK1, MK2, MK3 and MK4 (see notes below) Ruger Pistols (Very early MK1 may vary)You MUST have the COMPLETE "Accurizing" or...

Volquartsen Ruger Mark 1, 2, 3, 4 ALL 22/45 and LITE Target Trigger BLACK

Fits Mark 1, 2, 3, 4 All 22/45 All LITECNC-machined Target Trigger features both pretravel and overtravel adjustments. Made of Aluminum Other trigger colors here UPC: 810162011475Model: VC2TT

Volquartsen Pistol Competition Kit for Mark 1, 2, 3 Black Trigger (Scorpion) VC2PCK-B

Trying to figure out which parts are needed to take the Ruger MKII, MKIII and 22/45 to the next level? Look no further than the Pistol Competition Kit. This kit includes: -Accurizing Kit-Bolt Tune-Up Kit-CNC-Machined Disconnector. The Pistol Competition...

Volquartsen Black Extended Magazine Release For Ruger 22/45 Mark 3

Only Fits Ruger 22/45 Mark 3 frames **DOES NOT FIT ANYTHING ELSE**Will not fit 22/45 Mark 2 The MKIII Extended Magazine Release is an 1/8” longer than the factory release providing easier access. This release has also been modified to improve...

Volquartsen VS3 Recoil Rod Replacement Spring STANDARD for Ruger Mark 1, 2, 3, 4 and ALL 22/45 and LITE VC3RS SILVER

Replacement Spring for the VC3RS Kit ORIf you know what you are doing you can replace your spring on your factory Ruger KA-57 AssemblySILVER Standard Weight is a direct replacement for the Ruger KA-57 recoil assembly.(I think it's actually lighter though...

Volquartsen Magazine Follower Button for Ruger Mark 1, 2, 3, 4 Pistols - 10 Pack OLD style

Have a sluggish MKII, MKIII, MK IV, or 22/45 Ruger magazine? Chances are the spring is fine but the actual culprit is the metal on metal contact of the magazine button. Not only does this make magazines hard to load but it can also cause feeding...

Volquartsen SureStrike Firing Pin for Ruger Mark 1, 2, 3, 4 and ALL 22/45 and LITE

Volquartsen SureStrike Firing Pin is designed to minimize and/or eliminate light hits on the Ruger MKI, MKII and MKIII (including 22/45) pistol. The SureStrike Firing Pin is precision EDM machined from A2 tool steel. The impact section of the firing pin...

Volquartsen Ruger Mark 1, 2, 3, 4 ALL 22/45 and LITE Target Trigger STAINLESS

Fits Mark 1, 2, 3, 4 All 22/45 All LITECNC-machined Target Trigger features both pretravel and overtravel adjustments. Made of Aluminum Other trigger colors here UPC: 810162012441Model: VC2TT-ST

Volquartsen Ruger Mark 2, 3 Aluminum Target Grip Frame (Lower) Black (Scorpion)- VC3NF-B

Volquartsen TARGET frame Same as the Standard steel Ruger frames only aluminum and MUCH BETTER!!These will work with MK2 uppers also.About 5 ounces lighter than the Ruger Steel Frame.These frames will accept Ruger, Tac-Sol and most likely AMT uppers.They...

Volquartsen Magazine Follower Button for Ruger Mark 1, 2, 3, 4 Pistols - 2 Pack OLD style

Have a sluggish MKII, MKIII, MK IV, or 22/45 Ruger magazine? Chances are the spring is fine but the actual culprit is the metal on metal contact of the magazine button. Not only does this make magazines hard to load but it can also cause feeding...

Volquartsen Target Rear Sight for Mark 2, 3, 4 Series- VC2TL

Fits Ruger Mark Uppers (the sight for the LLV is here)Replacement Rear sight designed specifically for Mark 2, 3, and 4 uppers with 0.875" bull barrels. The sight for LLV is a little higher and will NOT work for these. Drop-in sights use existing...

Volquartsen Pistol Competition Kit for Ruger Mark 1, 2, 3 Stainless Trigger (Scorpion) VC2PCK-S-ST

Trying to figure out which parts are needed to take the Ruger MKII, MKIII and 22/45 to the next level? Look no further than the Pistol Competition Kit. This kit includes: -Accurizing Kit-Bolt Tune-Up Kit-CNC-Machined Disconnector. The Pistol Competition...

Volquartsen 22/45 Auto Bolt Release for Ruger Mark 3 ONLY Pistols Silver VC3SPL-S

WILL NOT FIT ANY STANDARD FRAMEWas told by customer will NOT fit 22/45 Mark 2 eitherThey have made releasing the bolt on the Ruger 22/45 easier. No more having to manually operate the bolt hold open lever to release the bolt. Simply pull back on the bolt...

Volquartsen Accurizing Kit Fits Mark 1 2 3 Stainless Trigger VC2AK-S-ST

THIS is the kit you want for your Mark 3 to remove Magazine safety. Complete drop-in kit comes complete with:-Target Hammer-Target Sear-Target Trigger (available in a variety of colors)-Extended Bolt Release-Trigger Return Spring with...

Factory Ruger KA-57 Recoil Rod Spring Assembly for ALL Ruger Mark 1 2 3

Factory Ruger KA-57 Recoil Spring Assembly for Mark 1 2 3.Seen these bent, worn out and lost.

Volquartsen Stainless Extended Magazine Release For Ruger 22/45 Mark 3

Only Fits Ruger 22/45 Mark 3 frames **DOES NOT FIT ANYTHING ELSE**Will not fit 22/45 Mark 2 The MKIII Extended Magazine Release is an 1/8” longer than the factory release providing easier access. This release has also been modified to improve...

Volquartsen SILVER Dovetail Picatinny Rail Mount for ALL Mark 1 2 3 4

THESE ARE SILVERThese are LONG discontinued, we just ran across some more.The Volquartsen Dovetail Scope Mount converts the sight dovetail on a Ruger Mark 1, 2, 3, 4, all 22/45 and LITE Pistols to a Picatinny style mount. This mount is the perfect...

Volquartsen Mark 3 LLV - Scorpion Silver Compensator VC3CL-S

Multi-Port Scorpion Comp for Mark 2 and 3 LLV ONLYMatches the LLV profile, so works on the Volquartsen Scorpion or Black Mamba, CNC-machined from a solid billet and finished for durability. Uses a knurled nut to tighten on muzzle threads. Pin wrench for...

Volquartsen Ruger Mark 3 Aluminum 1911 Style (22/45) Grip Frame (Lower) OD Green (Scorpion) VC45NF-OD

Volquartsen 1911 Style frame Same as the 22/45 Zytel (Polymer) Ruger frames only aluminum and MUCH BETTER!!Use this frame if you already shoot 1911 in something else.These will work with MK2 uppers also.These frames will accept Ruger, Tac-Sol and most...

Volquartsen Ruger Mark 1, 2, 3, 4 ALL 22/45 and LITE Target Trigger GOLD

Fits Mark 1, 2, 3, 4 All 22/45 All LITECNC-machined Target Trigger features both pretravel and overtravel adjustments. Made of Aluminum Other trigger colors here UPC: 810162019549Model: VC2TT-GT

Birchwood Casey Synthetic Gun Oil, 2 fl. oz. Pump Spray 44123

VERY COOL PUMP SPRAY BOTTLE with SYNTHETIC OIL!!!I had been looking for such a thing for myself!Please note: This item cannot be shipped to an address within the State of California.A superior gun oil for all climates. Reduces the friction between mating...

Volquartsen 4.5" Mark 2, 3 LLV (Scorpion Upper) Black 1/2"x28 Threads VC2LLV-B-4

FFL REQUIRED (see instructions below)Volquartsen 4.5" Mark 2, 3 LLV (Scorpion Upper) 1/2"x28 ThreadsCNC-machined from a solid billet of aluminum and then contoured to shave off weight without sacrificing accuracy, this is the foundation of your...

Volquartsen *ROSE GOLD* Competition Bolt for Mark 4 IV and Mark 2 (Mamba, Scorpion)

Fits ALL Mark 2 and ALL Mark 4 ALL Standard and 22/45 and LITE Will fit ALL Mark 3 if LCI is removed from receiver or replaced by a filler.Are you a competitive shooter looking to eliminate stovepipes, failures to fire and improve the overall performance...

FTV 6" Volquartsen OPTICS READY Mark 2, 3 (Flat Top LLV Scorpion Upper) Black 1/2"x28 Threads with Comp

FFL REQUIREDVolquartsen OPTICS READY MK2 / MK3 FTV 6"Includes Single Port Compensator These are made to bolt a Vortex Venom Red Dot sight direct to the upperI'm not sure but I would expect some other Red Dot Sights would be compatibleThis fits on ANY...

Volquartsen Mark 3 LLV -Scorpion Black Compensator- VC3CL-B

Multi-Port Scorpion Comp for Mark 2 and 3 LLV ONLYMatches the LLV profile, so works on the Volquartsen Scorpion or Black Mamba, CNC-machined from a solid billet and finished for durability. Uses a knurled nut to tighten on muzzle threads. Pin wrench for...

Volquartsen Ruger Mark 3 Aluminum 1911 Style (22/45) Grip Frame Black VC45NF-B

Volquartsen 1911 Style frame Same as the 22/45 Zytel (Polymer) Ruger frames only aluminum and MUCH BETTER!!Use this frame if you already shoot 1911 in something else.These will work with MK2 uppers also.These frames will accept Ruger, Tac-Sol and most...

Volquartsen 6" Mark 2, 3 LLV (Scorpion Upper) Black 1/2"x28 Threads- VC2LLV-B-6

FFL REQUIRED (see instructions below)Volquartsen 6" Mark 2, 3 LLV (Scorpion Upper) 1/2"x28 ThreadsCNC-machined from a solid billet of aluminum and then contoured to shave off weight without sacrificing accuracy, this is the foundation of your...

NEW/OPEN BOX Volquartsen 22/45 Mainspring for Ruger Mark 2, 3 Pistols Black

OPEN-RETURN NO ISSUES-AS NEW   These mainsprings are NEW, but are from OPEN PACKAGING. They were returned by owners of standard frame marks who mistakenly bought the wrong mainspring. Totally unused.WILL NOT FIT ANY STANDARD FRAMEComplete...

Volquartsen Mark 3 LLV - Scorpion Black Single Port Compensator- VC3CL-ST-SP-B

Single Port Scorpion Comp for Mark 2 and 3 LLV ONLYMatches the LLV profile, so works on the Volquartsen Scorpion or Black Mamba, CNC-machined from a solid billet and finished for durability. Uses a knurled nut to tighten on muzzle threads. Pin wrench for...

Volquartsen 4.5" Mark 2, 3 LLV (Scorpion-X Upper) Black NON-Threaded VC2LLV-0095

FFL REQUIRED (see instructions below)Volquartsen Scorpion-X LLV Upper-4.5", NON-Threaded for Mark II & III CNC-machined from a solid billet of aluminum and then contoured to shave off weight without sacrificing accuracy, this is the foundation of your...

Volquartsen Mark 3 LLV Scorpion Black Accessory Rail VCSN-R

This accessory rail mounts to the underside of the barrel on the Scorpion Pistol and LLV Competition Pistol Upper.NOT ALL SCORPION OR MARK 3 LLV UPPERS ARE DRILLED AND TAPPED FOR THIS RAIL!!PLEASE CHECK YOURS BEFORE ORDERINGModel: VCSN-R

Volquartsen Accurizing Kit Fits Mark 1 2 3 GOLD Trigger (Scorpion)

THIS is the kit you want for your Mark 3 to remove Magazine safety. Complete drop-in kit comes complete with:-Target Hammer-Target Sear-Target Trigger (available in a variety of colors)-Extended Bolt Release-Trigger Return Spring with...

Volquartsen 3" Mark 2, 3 LLV (Scorpion Upper) Black 1/2"x28 Threads VC2LLV-0098

FFL REQUIRED (see instructions below)Volquartsen 3" Mark 2, 3 LLV (Scorpion Upper) 1/2"x28 ThreadsCNC-machined from a solid billet of aluminum and then contoured to shave off weight without sacrificing accuracy, this is the foundation of your lightweight...