HANDGUN

Chiappa Rhino Mainspring (do your own trigger job)

Genuine Chiappa Rhino Mainspring THESE FIT ALL RHINO REVOLVERSPlay with your own trigger job and keep your original as it was.

Factory Ruger Mark III Internal Lock Key

Ruger Internal Lock Key that ships with new key-enabled handguns (LC9®, Mark III™, P345®)

Volquartsen Posi-Lock Bolt Latch for Ruger Mark 2 and 3

Are you tired of having to replace your factory bolt hold open latch? Volquartsen's Posi-Lock Bolt Hold Open Latch has been engineered to withstand years of use for even the most demanding shooter.Manufactured from hardened A2 tool steel this latch...

Factory Issued Ruger Instruction / Owner's Manual - Mark IV Pistols - MKIV 2/2021 R5

Factory Issued Ruger Instruction / Owner's Manual - Mark IV PistolsMKIV 2/2021 R5This is a Genuine Factory issued Ruger Owner’s Manual that was removed from a parted out firearm.Condition is "useable", most are very good and we toss any that we notice...

Volquartsen Silver Extended Bolt Release for Ruger Mark 4 IV *NOT* for 22/45

NOT for 22/45Finding it too hard release the bolt on the MK IV? This extended bolt release gives you more surface area and deep serrations for easy thumb engagement. The bolt release pad is CNC machined from 416 stainless and extends .050” further...

Factory Ruger 22/45 Mark 2 3 4 (IV) & LITE Trigger Pivot Retainer *F4*

WILL NOT FIT ANYTHING BUT 22/45 PLASTIC Frames Trigger Pivot Pin Retainer Factory Ruger part Mark IV Part #4 in Exploded ViewMark 3 Part #30 in Exploded ViewMark 2 Green Circle in Exploded View

Factory Ruger Picatinny Base Screw for Ruger "LITE" Reversible Picatinny Rail *E17*

This is ONE single screw, buy as many as you need (only 3 are needed on a Mark Receiver) These use 3/32" Allen Driver.The "Reversible" picatinny rail used on the LITE from the factory uses a shorter screw than the standard old style Weaver rails. The old...

Volquartsen Magazine Follower Button for Ruger Mark 1, 2, 3, 4 Pistols - 10 Pack OLD style

Have a sluggish MKII, MKIII, MK IV, or 22/45 Ruger magazine? Chances are the spring is fine but the actual culprit is the metal on metal contact of the magazine button. Not only does this make magazines hard to load but it can also cause feeding...

Volquartsen SureStrike Firing Pin for Ruger Mark 1, 2, 3, 4 and ALL 22/45 and LITE

Volquartsen SureStrike Firing Pin is designed to minimize and/or eliminate light hits on the Ruger MKI, MKII and MKIII (including 22/45) pistol. The SureStrike Firing Pin is precision EDM machined from A2 tool steel. The impact section of the firing pin...

Volquartsen V-Lock Retainer Spring for Mark IV Pistols

Fits all Ruger Mark IV standard and 22/45 frames.This retainer stops your bolt stop cross pin from drifting out of place during heavy use without impacting your ability to disassemble you Mark.Installation instructions hereUPC: 810162018641Model: V4LS

Factory Ruger Hammer Strut for Mark Series 1, 2, 3 and MK 2 3 22/45 Pistols *A17

Factory Ruger Hammer Strut for ALL Mark 1, 2 and 3 Pistols including 22/45 versionsNOT FOR ANY MARK 4 PISTOLS

Factory RUGER Mark 2 Black Plastic Checkered Grips *RG2

Factory Ruger Mark II Black Plastic Checkered Grips Includes 4 grip screwsFits Mark II STANDARD Frame pistols, as well late Mark I (A-100) FramesWILL NOT FIT ANY 22/45 WILL NOT FIT EARLY MARK 1 "A-54" FRAMEModel: 19932UPC: 736676199327Looking for the...

Volquartsen Target Rear Sight for LLV (Scorpion, Mamba) and LLV-4 (Mamba) VC2TL-H

ONLY FITS LLV UPPERS. (the sight for Ruger Mark Uppers is here)Replacement Rear sight designed specifically for Volquartsen Uppers. Will NOT work for Ruger uppers as its too tall for factory Ruger front sights.Model: VC2TL-HUPC: 810162014711

Smith & Wesson 10 round magazine for SW22 Victory 3001520

Factory Smith & Wesson SW22 Victory 10 round magazine

Factory Ruger Black Trigger for Mark 1 2 3 Pistols

These have the Tab on the back which was for Mark 3, some compliant thing for CA at one time I think (if you know more fill me in)That tab may need to be ground off in some installationsThis trigger is a bit different than Mark IV, have not tried to see...

Factory Ruger Sight Elevator - Elevation Spring for Adjustable Handgun Sights *D10*

Fits ALL Ruger Adjustable Sight Mark Series Pistols (see notes below)Ruger "LITE" is still a Mark series pistolRuger Mark IV pistols from late 2018 on have a NEW rear sightThis part is NOT compatible with the new design sight (see pictures above) This...

Factory Ruger Rear Sight ALLEN Lock Screw Mark 1 2 3 4 IV and 22/45 *D3*

Fits most Ruger Mark Series Pistols (see notes below)Ruger Mark IV pistols from late 2018 on have a NEW rear sightThis part is NOT compatible with the new design sight (see pictures above)Very early Adjustable sights were "MICRO" brand and I'm not sure...

HiViz Fiber Optic Ruger 22/45 LITE Mark 3 4 IVand Tac-Sol Pac-Lite, LiteWave Front Sight

Improve the performance of your Ruger 22/45 LITE with the new Fiber Optic LITEWAVE® sight. Our bright and ultra-durable LITEWAVE® sights will enhance your confidence and shooting experience. This is NOT for standard Bull Barrels, only Aluminum 1"...

Volquartsen Ruger Mark 1, 2, 3, 4 ALL 22/45 and LITE Target Trigger STAINLESS

Fits Mark 1, 2, 3, 4 All 22/45 All LITECNC-machined Target Trigger features both pretravel and overtravel adjustments. Made of Aluminum Other trigger colors here UPC: 810162012441Model: VC2TT-ST

Factory Ruger Sight Blade for Adjustable Handgun Sights .125" Black *D23

Fits ALL Ruger Mark Series Pistols (see notes below)Ruger "LITE" is still a Mark series pistolRuger Mark IV pistols from late 2018 on have a NEW rear sightThis part is NOT compatible with the new design sight (see pictures above) .125" Blade with Black...

Volquartsen Mark 4 LLV-4 - Mamba, Black Compensator- VC4CL-B

ONLY FITS/MATCHES VOLQUARTSEN MK4 LLV-4 UPPERTechnically fits Black Mamba and Scorpion, yes, but does NOT match those contours, ONLY matches the MK4 LLV-4Black Alloy CompensatorFor MK4 LLV-4 Model; VC4CL-B

Volquartsen Stainless Extended Magazine Release For Ruger Mark 3

Fits Ruger Mark 3 Standard frames **DOES NOT FIT ANY 22/45** The MKIII Extended Magazine Release is an 1/8” longer than the factory release providing easier access. This release has also been modified to improve insertion of the factory...

TacSol Tactical Solutions Pac-Lite Picatinny Sight Rail PLSR-STD

Tactical Solutions Pac-Lite Standard Picatinny Sight Rail BE AWARE that that the Pac-Lite uses same hole spacing as RugerBUTThey use a 6-40 screw NOT a 6-48 screw like RugerPac-Lite = 6-40Ruger = 6-48(for those that do not know the 40 and 48 are how many...

Factory Ruger Mark IV 4 Bolt Stop Cross Pin for 22/45 FRAME *F11

Factory Ruger Mark IV 22/45 Bolt Stop Cross PinWill NOT fit anything but MARK IV22/45 frame ONLYDoes NOT fit STANDARD, it's too LONGPart #39 in Ruger ManualThe Bolt Stop Cross Pin Retainer is HERE

Factory Ruger Hammer Strut Pin for Mark 1 & 2 Pistols and MK2 22/45 *A14B

Factory Ruger Hammer Strut Pin Fits Mark Series 1 and 2 Pistols and 22/45 Mark 2. This pin is for Mark 1, 2 series only BUT is the same pin as Mark 3 only LONGER. The MK3 hammer is thinner in this area due to the magazine disconnect. These are "staked"...

Ruger 10 round NICKEL 90231 Magazine with SILVER Base for Mark 3 4 IV Standard Frame Pistols

WILL NOT FIT 22/45Factory Ruger 90231 10 round magazine with SILVER BASE 90231 is what Ruger shipped with new Mark 3 and ships with Mark 4 pistols.This magazine will also work in Mark 2 and Mark 1 pistols.For older Mark 1 (right hand follower button)...

Volquartsen Magazine Follower Button for Ruger Mark 1, 2, 3, 4 Pistols - 2 Pack OLD style

Have a sluggish MKII, MKIII, MK IV, or 22/45 Ruger magazine? Chances are the spring is fine but the actual culprit is the metal on metal contact of the magazine button. Not only does this make magazines hard to load but it can also cause feeding...

Factory Ruger 22/45 Mark 3 4 (IV) and LITE Trigger Pivot Pin *F19

WILL NOT FIT ANYTHING BUT,22/45 Mark 3, 4LITE Mark 3, 4*NOT for STANDARD Frames* (Some LITE now come with Standard frames PAY ATTENTION!!) Trigger Pivot Pin Factory Ruger part Part #34 in Exploded View

Slotted Factory Ruger front sight screw 6-40 threads for Ruger Mark 1 2 3 4 IV & All 22/45 (except LITE) Pistols *E12

This is the old Flat Blade Driver type screw for Front sights used on Mark Series Bull barrels.Ruger switched to slightly longer Allen screws in maybe 2017This is 6-40 threads, NEWER post October 2019 Mark IV STEEL barrels use a 6-48 screw so PAY...

Factory Ruger Bolt Stop Plunger for Mark 2, 3 Pistols NOT 22/45 *A10

Factory Ruger Bolt Stop Plunger Fits Mark Series 2 or 3 Pistols. Will not fit any 22/45 and not needed on Mark 1 series. NOT FOR MARK 1 or 4 or ANY 22/45 or LITEIf your bolt stop is acting odd you may need a new spring

Ruger Wrangler, Blackhawk, Single Six, Vaquero Rosewood Laminated Wood Grips NO LOCK 46

Factory Ruger Rosewood Grips for Vaquero and Blackhawk* *For XR3-Red Frame revolvers WITHOUT internal lock. This includes: -Wrangler-Old Army-New Model Single-Six-Super Single-Six-Single-Ten-New Model Blackhawk-New Model Super Blackhawk with ROUND...

Ruger Mark IV 4 STANDARD NEW Take Off Upper 6" Standard Taper Barrel with Sights 40105

New Take OffRuger 6" Standard Taper Steel UpperGreat start for a Custom Barrel Project or internally suppressed project.From a technical stand, it is longer and lighter than the 5.5 Bull and offers great balanceDrilled and tapped for a Rail MountFits ALL...

Factory Ruger Mark IV 4 Bolt Stop for STANDARD Frames (DOES NOT WORK WITH 22/45) *C12

Factory Ruger Mark IV Bolt Stop for STANDARD FramesWill NOT fit anything but MARK IVSTANDARD frame ONLYClick HERE for the 22/45 versionPart #7 in Ruger Manual

Trigger Pivot Pin RETAINER Fits Ruger A-54 and A-100 frames Mark 1 ONLY! *B17

Trigger Pivot Pin Retainer Fits Ruger Mark 1 A-54 and A-100 frames, as well as Volquartsen Aluminum Mark 3 framesMark 2 and 3 Ruger frames use a wire spring type retainer but this can be used in its place on steel frames.22/45 needs the wire retainer to...

Factory Ruger Mark IV 4 Wrap Around Finger Groove Laminated Wood Grips (also fits and Volquartsen Mamba)

WILL NOT FIT ANY 22/45ONLY FITS Mark IV Standard FramesSmoothly contoured, comfortable laminate grip features natural pointing grip angle with checkered grip panels for a non-slip hold. Finger groove grips provide a solid hold, even with sweaty hands...

Factory Ruger Mark III 3 Wrap Around Finger Groove Laminated Wood Grips

WILL NOT FIT ANY 22/45ONLY FITS Mark III Standard FramesSmoothly contoured, comfortable laminate grip features natural pointing grip angle with checkered grip panels for a non-slip hold. Finger groove grips provide a solid hold, even with sweaty hands...

Factory Ruger Front Sight Blade ONLY for 75TH Anniversary Pistol 6-7/8" Thin Taper Barrel *J16*

Factory Ruger ONLY for 75TH Anniversary Pistol 6-7/8" Thin Taper Barrel The front sight on your pistol should use a set SCREW (not pin). Please see all pictures before buying.

Volquartsen Target Rear Sight for Mark 2, 3, 4 Series- VC2TL

Fits Ruger Mark Uppers (the sight for the LLV is here)Replacement Rear sight designed specifically for Mark 2, 3, and 4 uppers with 0.875" bull barrels. The sight for LLV is a little higher and will NOT work for these. Drop-in sights use existing...

Ruger Short Red Ramp Plunger Latch Front Sight for GP100 and Super Redhawk (and more) Revolvers

This is a Plunger Latch front sightThere will be a hole right above the muzzle that has a spring loaded plunger in it that holds the sight in place.If you do not have a hole there,, this sight is NOT for you,,,These typically fit;Some GP100Some Super...

Factory Ruger Sear Spring Stop Pin for Mark Series 1 2 3 Pistols (NOT 22/45) *A18

Factory Ruger Sear Spring Stop Pin for Mark Series 1, 2 and 3 PistolsThis is the same pin used for Mark 1 & 2 Standard Frame Magazine Latch NOT FOR ANY 22/45 or LITETHESE MAY BE BLUED OR STAINLESSNO CHOICEDEPENDS ON WHAT THEY SHIP US

Factory Ruger Hammer Pivot Pin Stainless for Mark 2, 3 (NOT 22/45) Pistols *A23

Hammer Pivot Pin Fits Ruger Mark Series 2 or 3This is the STAINLESS version, BLUED version is hereNOT FOR ANY 22/45 or any MARK 4These can provide contrast when mixing stainless in a blued frame.

Factory Ruger Stainless Bolt Stop Release for Mark 2, 3 Pistols *NOT 22/45* *A14

Factory Ruger Stainless Bolt Stop Release Fits Mark Series 2 or 3 Pistols. Will not fit 22/45 and not needed on Mark 1 series. We find that putting Stainless in a Blued frame adds a nice accent. We carry the BLUED version as well!   NOT FOR MARK 1...

NEWER Style Front Sight Blade SET SCREW for Ruger Mark 4 IV Pistols with Taper Barrels *E9*

This SET SCREW is for the NEWER Style Factory Ruger Front Sight Blade for Standard tapered barrels and the 75th Anniversary 40175 Model SEE PICTURES If you have an empty hole on the right side of your Front Sight, this is the set screw that goes in there...

Hogue RUGER 22/45 MK IV G-MASCUS G10 PIRANHA GRIP PANELS

Hogue RUGER 22/45 MK IV G-MASCUS G10 PIRANHA GRIP PANELSThese grips WILL NOT work for STANDARD frames.These are new take-off grips from model 43920 Iron Valley exclusive Mark IV 22/45 LITE. They're made by Hogue for the 43920 Mark IV LITE.

TacSol Tactical Solutions Trail-Lite REPLACEMENT Thread Protector (End Cap) Matte Black 1/2"x28

Tactical Solutions Trail-Lite Replacement Thread Protector ANODIZING WILL NEVER BE AN EXACT MATCH FINISHBuy the color that matches your barrel OR set it off with another color!-for Trail-Lite (current version) and Browning Buck Mark -1/2"x28 ThreadsOther...

Slotted Factory Ruger Sight Elevator - Elevation Screw for Adjustable Handgun Sights *D9*

Fits ALL Ruger Adjustable Sight Mark Series Pistols (see notes below)Ruger "LITE" is still a Mark series pistolRuger Mark IV pistols from late 2018 forward have a NEW rear sight This part is NOT compatible with the new design sight with TWO SET SCREWS...

Volquartsen Mark IV 22/45 Magazine Base Pad and Extended Magazine Release Kit 5 Pack

This kit includes both the extended mag release for the Ruger Mark IV 22/45 and the new Magazine Base Pads for the Mark IV 22/45. The CNC-machined aluminum base pads make magazine insertion and removal quicker and easier-for lightning fast reloads and...

Factory Ruger 22/45 Mark 3 and MK3 LITE Sear Pivot Pin *F18*

Factory Ruger Sear Pivot PinONLY FITS 22/45 Mark 3 and Mark 3 LITENOT for any Standard Frame or ANY Mark 2 or Mark IVONLY FITS MARK 3 22/45 and MARK 3 LITE

Factory RUGER Mark 3 Ivory Checkered Plastic Grips

Factory RUGER Mark 3 Ivory Checkered Plastic Grips. Comes with screws. Can be used on Mark 2 see pics for what will showCan also be used on Mark 1 but NOT A-54 frame (Pre-1972) WILL NOT FIT ANY 22/45Genuine Ruger Factory Accessory Model: 19933UPC:...

Volquartsen 22/45 Auto Bolt Release for Ruger Mark 3 ONLY Pistols Silver VC3SPL-S

WILL NOT FIT ANY STANDARD FRAMEWas told by customer will NOT fit 22/45 Mark 2 eitherThey have made releasing the bolt on the Ruger 22/45 easier. No more having to manually operate the bolt hold open lever to release the bolt. Simply pull back on the bolt...

Volquartsen CNC-Machined Disconnector (trigger Bar) for MKII and MKIII - VC2DN

VC2DN CNC-Machined Disconnector is CNC-machined from 416 stainless steel. The machining process allows us to make several design changes to the the way the disconnector functions. We have added material that increases rigidity over the current design...

Volquartsen Accurizing Kit Fits Mark 1 2 3 Stainless Trigger VC2AK-S-ST

THIS is the kit you want for your Mark 3 to remove Magazine safety. Complete drop-in kit comes complete with:-Target Hammer-Target Sear-Target Trigger (available in a variety of colors)-Extended Bolt Release-Trigger Return Spring with...